Showing 1–9 of 116 results
-
1 Inch C.O.R.A. I 7075 Aluminum
High-strength aluminum Alloy ring, with integral rail, clamps to anyQuick ViewHigh-strength aluminum Alloy ring, with integral rail, clamps to any 1″ diameter scope so you can mount flashlights, lasers, nightvision and other accessories to your favorite tactical arms. C.O.R.A. I features a single rail that accepts Mil-STD 1913 (Picatinny) and Weaver-style mounts. Four, Torx screws tighten the ring halves for superior holding power. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. 3/8″ (9.5mm) high from top of scope tube to bottom of rail. Accepts Weaver-style or Mil-STD 1913 (Picatinny) mounts.
-
1/2 Hex Nut – Package of two (2) Nuts
Fully compatible with USMC deployment kit. Works with military issued
Quick ViewFully compatible with USMC deployment kit. Works with military issued wrench. Simply remove existing 7/16 hex nuts from original equipment and replace with 1/2 hex nuts. It is compatible for the entire line of the TSR, TSR”W” and HRT scope rings in both the Aluminum alloy and Alloy Steel versions.
SPECS: 4140 Alloy Steel, black oxide finish to Mil-C-13924 standards. 1/2 Hex Nut (12.7mm). 1/4-28 Threads (6.35mm) diameter thru hole.
Designed specifically for factory replacement components for TPS rings.
-
30mm C.O.R.A. I 7075 Aluminum
High-strength aluminum Alloy ring, with integral rail, clamps to anyQuick ViewHigh-strength aluminum Alloy ring, with integral rail, clamps to any 30mm diameter scope so you can mount flashlights, lasers, nightvision and other accessories to your favorite tactical arms. C.O.R.A. I features a single rail that accepts Mil-STD 1913 (Picatinny) and Weaver-style mounts. Four, Torx screws tighten the ring halves for superior holding power. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. 3/8″ (9.5mm) high from top of scope tube to bottom of rail. Accepts Weaver-style or Mil-STD 1913 (Picatinny) mounts.
-
7/16 Hex Nut – Package of two (2) Nuts
Original factory replacement components for the entire line of theQuick ViewOriginal factory replacement components for the entire line of the TSR, TSR”W” and HRT scope rings in both the Aluminum alloy and Alloy Steel versions. SPECS: 4140 Alloy Steel, black oxide finish to Mil-C-13924 standards. 7/16 Hex Nut (11.11mm). 1/4-28 Threads (6.35mm) diameter thru hole. Designed specifically for factory replacement components for TPS rings.
-
BASEBED Alignment Bar
Aluminum alignment bar helps you achieve perfect alignment between theQuick ViewAluminum alignment bar helps you achieve perfect alignment between the scope ring bases and the receiver, with no lapping. Bases are aligned in three different planes before they are mounted on your weapon, ensuring perfect alignment when they are attached. Mounting epoxy, black dye and complete instructions included. SPECS: Aluminum, red. 6-5/8″ (16.8cm) long, 1″ (25mm) high.
-
Clamp Foot – Package of two (2) Clamps
Original factory replacement components for the entire line of theQuick ViewOriginal factory replacement components for the entire line of the TSR, TSR”W” and HRT scope rings in both the Aluminum alloy and Alloy Steel versions. SPECS: 4140 Alloy Steel, black oxide finish to Mil-C-13924 standards. 1/4″ (6.35mm) diameter thru hole. Designed specifically for factory replacement components for TPS rings.
