- You cannot add that amount of "TSR 26mm Low Alloy Steel" to the cart because there is not enough stock (0 remaining).
Showing 1–9 of 23 results
-
HRT 1 Inch Low 7075 Aluminum
HRT Series Rings, precisely machined from an aluminum billet, withQuick ViewHRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).
-
HRT 1 Inch Low Alloy Steel
HRT Series Rings, precisely machined from an alloy steel billet,Quick ViewHRT Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).
-
HRT 30mm Low 7075 Aluminum
HRT Series Rings, precisely machined from an aluminum billet, withQuick ViewHRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – Low: .925″ (23.5mm).
-
HRT 30mm Low Alloy Steel
HRT Series Rings, precisely machined from an alloy steel billet,Quick ViewHRT Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – Low: .925″ (23.5mm).
-
TSR 1 Inch Low Alloy Steel
TSR Series Rings, precisely machined from an alloy steel billet,Quick ViewTSR Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).
-
TSR 1 Inch Low 7075 Aluminum
TSR Series Rings, precisely machined from an aluminum billet, withQuick ViewTSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).
-
TSR 30mm low 7075 Aluminum
TSR Series Rings, precisely machined from an aluminum billet, withQuick ViewTSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – Low: .925″ (23.5mm).
-
TSR 30mm Low Steel
TSR Series Rings, precisely machined from an alloy steel billet,Quick ViewTSR Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – Low: .925″ (23.5mm).
