HRT 1 Inch High 7075 Aluminum

7075 Aluminum Alloy Billet

Showing 1–9 of 50 results

  • HRT 1 Inch High 7075 Aluminum

    0 out of 5
    HRT Series Rings, precisely machined from an aluminum billet, with

    HRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – High: 1.185″ (30mm).

    Add to cart
    $93.00
    Quick View
  • HRT 1 Inch Low 7075 Aluminum

    0 out of 5
    HRT Series Rings, precisely machined from an aluminum billet, with

    HRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).

    Add to cart
    $89.00
    Quick View
  • HRT 1 Inch Medium 7075 Aluminum

    0 out of 5
    HRT Series Rings, precisely machined from an aluminum billet, with

    HRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Medium: .985″ (25mm).

    Add to cart
    $89.00
    Quick View
  • HRT 1 Inch X-High 7075 Aluminum

    0 out of 5
    HRT 1 Inch 7075 Aluminum X-High Rings

    HRT 1 Inch 7075 Aluminum X-High Rings

    Add to cart
    $109.00
    Quick View
  • HRT 30mm High 7075 Aluminum

    0 out of 5
    HRT Series Rings, precisely machined from an aluminum billet, with

    HRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – High: 1.225″ (31.1mm).

    Add to cart
    $99.00
    Quick View
  • HRT 30mm Low 7075 Aluminum

    0 out of 5
    HRT Series Rings, precisely machined from an aluminum billet, with

    HRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – Low: .925″ (23.5mm).

    Add to cart
    $95.00
    Quick View
  • HRT 30mm Medium 7075 Aluminum

    0 out of 5
    HRT Series Rings, precisely machined from an aluminum billet, with

    HRT Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Weaver-type or Picatinny bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 30mm – Medium: 1.075″ (27.3mm).

    Add to cart
    $95.00
    Quick View
  • HRT 30mm S-Low 7075 Aluminum

    0 out of 5
    HRT SL (Super-Low) Series Rings, precisely machined from an aluminum

    HRT SL (Super-Low) Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing an attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from the top of base to center of the ring. 30mm – Super Low: .820″ (20.8mm).

    Add to cart
    $109.00
    Quick View
  • HRT 30mm X-High 7075 Aluminum

    0 out of 5
    HRT Rings from TPS are precisely machined from aluminum billet,

    HRT Rings from TPS are precisely machined from aluminum billet, with tolerances held to .0002″ to provide maximum scope/ring contact. They hold scopes securely against heavy recoil. The four-screw cap lets you align the reticle; tighten the left side of the cap, then the right side without the scope rotating. The radiused edges and corners help prevent snagging while providing attractive appearance and the large clamp-nut lets you torque the rings to Weaver or Picatinny bases.

    Add to cart
    $119.00
    Quick View
X