TSR Series Rings, precisely machined from a 7075 solid billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. A four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing an attractive appearance. Large, clamp-nut lets you torque rings to Weaver-style or Mil-STD 1913 (Picatinny) bases. SPECS: Alloy 7075 Aluminum finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from the top of base to center of the ring. 34mm – Low: 1.02362″ (26mm).

TSR W-Series Rings, precisely machined from a 7075 solid billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. A four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing an attractive appearance. Large, clamp-nut lets you torque rings to Weaver-style or Mil-STD 1913 (Picatinny) bases. SPECS: Alloy 7075 Aluminum finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from the top of base to center of the ring. 34mm – Low: 1.02362″ (26mm).

CUSTOM SIZE

TSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. A four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing an attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from the top of base to center of the ring. 30mm – Custom Low: .920″ (23.36mm).

This is a custom-size inventory overrun from a large OEM Customer build.  When these are gone, they are gone forever.

WRT Series X-Rings, bringing a whole new level of beauty and precision into an extremely rugged Weaver or Picatinny platform scope mount.

The XW-Rings have been built from the bottom up to provide the extreme precision and accuracy that TPS rings have been known for over the last two decades.  The ring bases begin from a solid billet of 6061-T651 aluminum and are then machined with a Single-Lug Weaver-style (.140 Width) recoil shoulder from the solid billet.  We have designed and engineered the Single-Lug recoil system to allow the parallelism and perpendicularity of the lugs to the ring bore to be within .0002, thereby providing repeatability that no other mount in the world with similar integrated lugs has done before.

The XW-Rings are specifically designed for both the Weaver-style (.150 width recoil slot) as well compatible with a Mil-STD 1913 rail system.

The ring caps are secured with Four (4) 8-32 x 1/2″ Camcar-Textron Torx drive screws and with the same unique design that allows you to tighten the left side of the cap, then the right side without the scope rotating.  The edges and corners are fully radiused, preventing snagging, and providing a beautiful appearance to your rifle.
The rings are securely attached to your rail with an oversized clamp system using Two (2) 8-32 x 1/2″ Camcar-Textron Torx screws, preventing any chance your rings will loosen or move once installed.

With unparalleled precision and holding force, and sleek design, these will meet the extreme expectations of any class shooter. SPECS: 6061-T6511 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. .700″ (17.8mm) wide. Height measured from the top of base to center of the ring. 30mm – Medium: 1.075″ (27.3mm).

WRT Series X-Rings, bringing a whole new level of beauty and precision into an extremely rugged Weaver or Picatinny platform scope mount.

The XW-Rings have been built from the bottom up to provide the extreme precision and accuracy that TPS rings have been known for over the last two decades.  The ring bases begin from a solid billet of 6061-T651 aluminum and are then machined with a Single-Lug Weaver-style (.140 Width) recoil shoulder from the solid billet.  We have designed and engineered the Single-Lug recoil system to allow the parallelism and perpendicularity of the lugs to the ring bore to be within .0002, thereby providing repeatability that no other mount in the world with similar integrated lugs has done before.

The XW-Rings are specifically designed for both the Weaver-style (.150 width recoil slot) as well compatible with a Mil-STD 1913 rail system.

The ring caps are secured with Four (4) 8-32 x 1/2″ Camcar-Textron Torx drive screws and with the same unique design that allows you to tighten the left side of the cap, then the right side without the scope rotating.  The edges and corners are fully radiused, preventing snagging, and providing a beautiful appearance to your rifle.
The rings are securely attached to your rail with an oversized clamp system using Two (2) 8-32 x 1/2″ Camcar-Textron Torx screws, preventing any chance your rings will loosen or move once installed.

With unparalleled precision and holding force, and sleek design, these will meet the extreme expectations of any class shooter. SPECS: 6061-T6511 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. .700″ (17.8mm) wide. Height measured from the top of base to center of the ring. 30mm – Low: .925″ (23.5mm).

WRT Series X-Rings, bringing a whole new level of beauty and precision into an extremely rugged Weaver or Picatinny platform scope mount.

The XW-Rings have been built from the bottom up to provide the extreme precision and accuracy that TPS rings have been known for over the last two decades.  The ring bases begin from a solid billet of 6061-T651 aluminum and are then machined with a Single-Lug Weaver-style (.140 Width) recoil shoulder from the solid billet.  We have designed and engineered the Single-Lug recoil system to allow the parallelism and perpendicularity of the lugs to the ring bore to be within .0002, thereby providing repeatability that no other mount in the world with similar integrated lugs has done before.

The XW-Rings are specifically designed for both the Weaver-style (.150 width recoil slot) as well compatible with a Mil-STD 1913 rail system.

The ring caps are secured with Four (4) 8-32 x 1/2″ Camcar-Textron Torx drive screws and with the same unique design that allows you to tighten the left side of the cap, then the right side without the scope rotating.  The edges and corners are fully radiused, preventing snagging, and providing a beautiful appearance to your rifle.
The rings are securely attached to your rail with an oversized clamp system using Two (2) 8-32 x 1/2″ Camcar-Textron Torx screws, preventing any chance your rings will loosen or move once installed.

With unparalleled precision and holding force, and sleek design, these will meet the extreme expectations of any class shooter.

SPECS: 6061-T6511 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. .700″ (17.8mm) wide. Height measured from the top of base to center of the ring. 30mm – S-Low: .820″ (20.8mm).

XRT Series X-Rings, bringing a whole new level of beauty and precision into an extremely rugged Picatinny platform scope mount.

The X-Rings have been built from the bottom up to provide the extreme precision and accuracy that TPS rings have been known for over the last two decades.  The ring bases begin from a solid billet of 7075-T6 aluminum and then machined with our unique Double-Lug Picatinny recoil shoulders from the solid billet.  We have designed and engineered the Double-Lug recoil system to allow the parallelism and perpendicularity of the lugs to the ring bore to be within .0002, thereby providing repeatability that no other mount in the world with similar integrated lugs has done before.

The X-Rings are specifically designed for the Mil-STD 1913 rail system.  Because of the Double-Lug system, they do require two (2) accompanied cross-slots in a 1913 cross-slot configuration.

The ring caps are secured with Four (4) 8-32 x 1/2″ Camcar-Textron Torx drive screws and with the same unique design that allows you to tighten the left side of the cap, then the right side without the scope rotating.  The edges and corners are fully radiused, preventing snagging, and providing a beautiful appearance to your rifle.
The rings are securely attached to your rail with an oversized clamp system using Two (2) 8-32 x 1/2″ Camcar-Textron Torx screws, preventing any chance your rings will loosen or move once installed.

With unparalleled precision and holding force, and sleek design, these will meet the extreme expectations of any class shooter.

SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. .700″ (17.8mm) wide. Height measured from the top of base to center of the ring. 30mm – High: .1.075″ (31.11mm).