TSR 1 Inch Low Alloy Steel

Picatinny (TSR)

Showing 1–9 of 32 results

  • TSR 1 Inch Low Alloy Steel

    0 out of 5
    TSR Series Rings, precisely machined from an alloy steel billet,

    TSR Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).

    Add to cart
    $99.00
    Quick View
  • TSR 1 Inch Medium 7075 Aluminum

    0 out of 5
    TSR Series Rings, precisely machined from an aluminum billet, with

    TSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. Medium: .985″ (25mm).

    Add to cart
    $89.00
    Quick View
  • TSR 1 Inch High 7075 Aluminum

    0 out of 5
    TSR Series Rings, precisely machined from an aluminum billet, with

    TSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – High: 1.185″ (30mm).

    Add to cart
    $93.00
    Quick View
  • TSR 1 Inch High Alloy Steel

    0 out of 5
    TSR Series Rings, precisely machined from an alloy steel billet,

    TSR Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – High: 1.185″ (30mm).

    Add to cart
    $103.00
    Quick View
  • TSR 1 Inch Low 7075 Aluminum

    0 out of 5
    TSR Series Rings, precisely machined from an aluminum billet, with

    TSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Low: .785″ (19.9mm).

    Add to cart
    $89.00
    Quick View
  • TSR 1 Inch Medium Alloy Steel

    0 out of 5
    TSR Series Rings, precisely machined from an alloy steel billet,

    TSR Series Rings, precisely machined from an alloy steel billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: Alloy Steel, black oxide finish to Mil-C-13924 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – Medium: .985″ (25mm).

    Add to cart
    $99.00
    Quick View
  • TSR 1 Inch X-High 7075 Aluminum

    0 out of 5
    TSR Series Rings, precisely machined from an aluminum billet, with

    TSR Series Rings, precisely machined from an aluminum billet, with tolerances held to .0002″, give maximum scope/ring contact. Holds scope securely against recoil. Four-screw cap lets you align the reticle, tighten the left side of the cap, then the right side without the scope rotating. Radiused edges and corners help prevent snagging while providing attractive appearance. Large, clamp-nut lets you torque rings to Mil-STD 1913 (Picatinny) bases. SPECS: 7075-T651 Aluminum Alloy, matte black, hard anodized to Mil-A-8625 standards. 5/8″ (15.8mm) wide. Height measured from top of base to center of ring. 1″ – X-High: 1.400″.

    Add to cart
    $109.00
    Quick View
  • TSR 26mm High Alloy Steel

    0 out of 5
    TSR Picatinny 26mm Alloy Steel High Rings

    TSR Picatinny 26mm Alloy Steel High Rings

    Add to cart
    $135.00
    Quick View
  • TSR 26mm Low Alloy Steel

    0 out of 5
    TSR Picatinny 26mm Alloy Steel Low Rings

    TSR Picatinny 26mm Alloy Steel Low Rings

    Add to cart
    $135.00
    Quick View
X